South African Class 7A 4-8-0

This article is about one of several different Cape Government Railways locomotive types to be designated "7th Class". For other CGR 7th Class locomotives, see Cape Government Railways 7th Class locomotives.

CGR 7th Class 4-8-0 1896
Sudan Railways Dongola Class
South African Classes 7A & 7AS 4-8-0

300px Ex CGR (Eastern System) 7th Class no. 726 SAR Class 7A no. 1009 with modified Type ZC tender

Type and origin ♠ - Original locomotive, as built ♥ - Locomotive equipped with superheating Power type Steam Designer Cape Government Railways (H.M. Beatty) Builder Sharp, Stewart and Company Dübs and Company Neilson and Company Serial number Sharp, Stewart 4145-4152, 4363 Dübs 3355-3362, 3641-3652, 3976 Neilson 4920-4931, 5160-5163, 5232-5234, 5280-5281, 5345-5347 Model CGR 7th Class Build date 1896-1898, 1901 Total produced 46

Specifications Configuration 4-8-0 (Mastodon) Driver axle 2nd coupled axle Gauge 3 ft 6 in (1,067 mm) Cape gauge Leading dia Coupled dia Tender wheels as built 34 in (864 mm) retyred Wheelbase 46 ft 2 in (14,072 mm)  • Engine  • Leading 5 ft 3 in (1,600 mm)  • Coupled 12 ft (3,658 mm)  • Tender 16 ft 1 in (4,902 mm)  • Tender bogie 4 ft 7 in (1,397 mm) Length:  • Over couplers Height 12 ft 10 in (3,912 mm) Frame type Plate Axle load ♠ ♥  • Leading ♠ ♥  • 1st coupled ♠ ♥  • 2nd coupled ♠ ♥  • 3rd coupled ♠ ♥  • 4th coupled ♠ ♥  • Tender axle av. Adhesive weight ♠ ♥ Loco weight ♠ ♥ Tender weight Loco & tender weight ♠ ♥ Tender type ZC (2-axle bogies) ZA, ZB, ZC, ZE permitted Fuel type Coal Fuel capacity 5 LT 10 cwt (5.6 t) Water cap Boiler:  • Pitch ♠ 6 ft 8 in (2,032 mm) pitch ♥ 6 ft 10 in (2,083 mm)  • Diameter ♠ 4 ft 4 in (1,321 mm) ♥ 4 ft 6 in (1,372 mm)  • Tube plates ♠♥ 10 ft 9 in (3,277 mm)  • Small tubes ♠ 185: ♥ 100:  • large tubes ♥ 18:  • Firebox type Round-top Boiler pressure ♠ 160 psi (1,103 kPa) 170 psi (1,172 kPa) adjusted ♥ 180 psi (1,241 kPa) Safety valve Ramsbottom Firegrate area ♠ 17.5 sq ft (1.63 m2) ♥ 18 sq ft (1.7 m2) Heating surface ♠ 1,078 sq ft (100.1 m2) ♥ 919 sq ft (85.4 m2)  • Tubes ♠ 976 sq ft (90.7 m2) ♥ 806 sq ft (74.9 m2)  • Firebox ♠ 102 sq ft (9.5 m2) ♥ 113 sq ft (10.5 m2) Superheater:  • Heating area ♥ 206 sq ft (19.1 m2) Cylinders Two Cylinder size 17 in (432 mm) bore 23 in (584 mm) stroke Valve gear Stephenson Valve type ♠ Slide, ♥ Piston Couplers Bell link-and-pin AAR knuckle (1950s)

Performance figures Tractive effort ♠ 18,660 lbf (83.0 kN) @ 75% ♠ 19,810 lbf (88.1 kN) @ 75% adjusted ♥ 22,240 lbf (98.9 kN) @ 75% Factor of adh 4.3

Career Operators Cape Government Railways Bechuanaland Railway Imperial Military Railways Imvani-Indwe Railway Sudan Military Railway South African Railways Zambesi Saw Mills Class CGR 7th Class, SAR Class 7A Number in class 46 CGR, 44 SAR Numbers CGR 347-350, 385-398, 718-744, 758 BR 4-7 IMR C522, C523 & C525-C527 Imvani-Indwe: Named SAR 988-1031 Sudan 26-33 Delivered 1896-1901 First run 1896 Withdrawn 1972

The leading coupled axle had flangeless wheels

The South African Railways Class 7A 4-8-0 of 1896 was a steam locomotive from the pre-Union era in the Cape of Good Hope.

Between 1896 and 1901, the Cape Government Railways placed a second batch of altogether 46 7th Class steam locomotives with a 4-8-0 Mastodon wheel arrangement in service on its Midland and Eastern Systems. In 1912, when all but two of them were assimilated into the South African Railways, they were renumbered and reclassified to Class 7A.

In 1897 and 1898, eight Cape 7th Class locomotives were also built for the Soudan Military Railway, during Kitchener's military campaign in Sudan.

Manufacturers

The original Cape 7th Class locomotive had been designed in 1892 by H.M. Beatty, at the time the Cape Government Railways (Western System) Locomotive Superintendent.

File:H.M. Beatty.jpg

H.M. Beatty

Following on the 38 7th Class locomotives which were placed in service by the Cape Government Railways (CGR) between 1892 and 1893, a second batch of slightly improved Cape 7th Class locomotives were acquired between 1896 and 1901. Outwardly, all these locomotives appeared almost identical to the first batch of 7th Class locomotives, but they had increased heating capacity as well as some other modifications. They were equipped with type ZC tenders, which rode on two two-axle bogies and had a capacity of 5 long tons 10 hundredweight (5.6 tonnes) coal and water.

1896

In 1896, orders were placed for twenty-eight locomotives, distributed between three manufacturers.

• Sharp, Stewart and Company built eight for the Midland System, numbered in the range from 385 to 392.
• Dübs and Company built eight for the Eastern System, numbered in the range from 718 to 723, 740 and 741.
• Neilson and Company built six for the Midland System, numbered in the range from 393 to 398, and another six for the Eastern System, numbered in the range from 724 to 729.

1897

File:Class 7A 1007 (4-8-0) BPR.JPG

x100px

In 1897, a further four 7th Class locomotives were ordered by the CGR from Neilson, along with three 6th Class locomotives, for use on the new Vryburg to Bulawayo line of the fledgling Bechuanaland Railway Company (BR). The line was still under construction and was operated by the CGR on behalf of the BR at the time. These 7th Class locomotives, numbered in the range from BR4 to BR7, were eventually returned to the CGR and renumbered in the range from 347 to 350, for the Midland System.

In 1897 and 1898, Neilson also built eight Cape 7th Class locomotives for the Soudan Military Railway, where they were known as the Dongola Class.

1898

In 1898, another ten 7th Class locomotives were taken into service by the CGR, as well as three by the Imvani-Indwe Railway, which operated a branchline from Sterkstroom to the Indwe Collieries in the Eastern Cape.

• Sharp Stewart built one 7th Class for the Imvani-Indwe, which was named E.J. Byrne by the colliery. It was eventually taken onto the CGR roster and became the Eastern System's no. 742.
• Dübs built two for the Imvani-Indwe, which were named Bradfield and Gardner Williams. They were also eventually taken onto the CGR roster and became the Eastern System's numbers 743 and 744 respectively.
• At the same time, Dübs built ten for the CGR, which were numbered in the range from 730 to 739 on the Eastern System.

1901

One more 7th Class locomotive was delivered by Dübs in 1901, and became the Eastern System's no. 758.

Class 7 sub-classes

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (CGR, Natal Government Railways and Central South African Railways) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways required careful planning and was only implemented with effect from 1 January 1912.

File:SAR Class 7A 1007 (4-8-0) ex CGR 724 ID.JPG

When all but two of these forty-six locomotives were assimilated into the South African Railways (SAR) in 1912, they were renumbered in the range from 988 to 1031 and designated Class 7A. The two exceptions had been sold to Pauling and Company in 1909.

The rest of the CGR's 7th Class locomotives, together with 7th Class locomotives from the Central South African Railways (CSAR), the Pretoria-Pietersburg Railway (PPR), the Rhodesia Railways (RR), the Natal Government Railways (NGR) and, in 1925, the New Cape Central Railways (NCCR), were grouped into six different sub-classes by the SAR, becoming SAR Classes 7 and 7B to 7F.

Modifications

During the 1930s and later, many of the Class 7 series locomotives were equipped with superheated boilers and piston valves. On the Class 7B and Class 7C, this conversion was sometimes indicated with an "S" suffix to the class number on the locomotive's number plates, but on the rest of the Class 7 family this distinction was rarely applied. The superheated versions could be visually identified by the position of the chimney on the smokebox, the chimney having been displaced forward to provide space behind it in the smokebox for the superheater header.

In the early 1960s, Class 7A no. 1021 was equipped with a superheater and reclassified to the sole Class 7AS. The number plate was altered by weld-writing a crude "S" after the "7A". This locomotive spent its last working days on the SAR doing steam heating tests on mainline passenger coaches at the Braamfontein North passenger yard in Johannesburg, before being sold to the Zambesi Saw Mills (ZSM) in 1971. The ZSM engineer's records, however, show it as not superheated and having saturated boiler no. 7865.

Renumbering

During their long service lives, some of the Class 7A locomotives underwent more than one renumbering. Five saw service with the Imperial Military Railways (IMR) and were temporarily renumbered accordingly, three were unnumbered, but named, while in Imvani-Indwe colliery service and all but two were eventually renumbered into the SAR's roster in 1912. The table below lists these renumberings as well as their builders and works numbers.

When the four BR locomotives, BR 4 to 7, were eventually returned to CGR service and renumbered in the range from 347 to 350 for the Midland System, it resulted in number duplication which confused historians in later years. These four engine numbers had been used previously on four of the 1892 and 1893 batch of 7th Class locomotives, also built by Neilson, which had since been renumbered in the range from 712 to 715 when they were transferred from the Midland to the Eastern System.

Class 7A builders, works numbers and renumbering

Builder	Works No.	Year	CGR No.	IMR or BR No.	Imvani-Indwe or Sold	SAR No.
Neilson	5160	1897	347	BR 4		1015
Neilson	5161	1897	348	BR 5	Pauling & Co.
Neilson	5162	1897	349	BR 6		1016
Neilson	5163	1897	350	BR 7		1017
Sharp Stewart	4145	1896	385			988
Sharp Stewart	4146	1896	386	C525		989
Sharp Stewart	4147	1896	387			990
Sharp Stewart	4148	1896	388			991
Sharp Stewart	4149	1896	389			992
Sharp Stewart	4150	1896	390			993
Sharp Stewart	4151	1896	391			994
Sharp Stewart	4152	1896	392			995
Neilson	4920	1896	393			996
Neilson	4921	1896	394			997
Neilson	4922	1896	395			998
Neilson	4923	1896	396	C522		999
Neilson	4924	1896	397			1000
Neilson	4925	1896	398		Pauling & Co.
Dübs	3355	1896	718			1001
Dübs	3356	1896	719			1002
Dübs	3357	1896	720			1003
Dübs	3358	1896	721			1004
Dübs	3359	1896	722			1005
Dübs	3360	1896	723	C527		1006
Neilson	4926	1896	724			1007
Neilson	4927	1896	725			1008
Neilson	4928	1896	726			1009
Neilson	4929	1896	727	C526		1010
Neilson	4930	1896	728			1011
Neilson	4931	1896	729			1012
Dübs	3643	1898	730	C523		1018
Dübs	3644	1898	731			1019
Dübs	3645	1898	732			1020
Dübs	3646	1898	733			1021
Dübs	3647	1898	734			1022
Dübs	3648	1898	735			1023
Dübs	3649	1898	736			1024
Dübs	3650	1898	737			1025
Dübs	3651	1898	738			1026
Dübs	3652	1898	739			1027
Dübs	3361	1896	740			1013
Dübs	3362	1896	741			1014
Sharp Stewart	4363	1898	742		EJ Byrne (No 3)	1028
Dübs	3641	1898	743		Bradfield	1029
Dübs	3642	1898	744		Gardner Williams	1030
Dübs	3976	1901	758			1031

Service

Cape Government Railways

The 7th Class series became the main goods locomotive class for the last twenty years of the existence of the CGR. Of this second batch of the Class, not all began their service lives on the CGR, and not all remained with the CGR until the SAR came into existence. In summary:

• Four originally began their service lives on the BR, between Vryburg in the Cape Colony and Bulawayo in Southern Rhodesia, and were eventually returned to the CGR and renumbered 347 to 350 for the Cape Midland.
• Four from the 1896 and one from the 1898 batches, saw service with the IMR during the Second Boer War from 1899 to 1902, having been allocated to the IMR for the duration of the war.
• Two locomotives, numbers 348 and 398, were sold to Pauling and Company in 1909, for use during the construction of the Rhodesia Katanga Junction Railway (RKJR) in Northern Rhodesia (Zambia). The RKJR purchased them from Paulings in 1910, after which they went to the Mashonaland Railway Company in 1928, and eventually to the RR in 1936. They retained their CGR engine numbers for their entire working lives, until they were scrapped by the RR in 1938.
• The Imvani-Indwe Railway's three 7th Classes were taken onto the CGR roster and numbered 742 to 744, for service on the Eastern System, before the 1912 amalgamation into the SAR.

South African Railways

In SAR service, the Class 7 series worked on every system in the country. In 1915, during the South West African Campaign in World War I, 29 Class 7 series locomotives were dispatched to South West Africa (SWA) to assist the expeditionary forces. Eleven of these were Class 7A locomotives, numbers 1000 to 1002, 1005, 1006, 1017, 1019 and 1021 to 1024.

They proved so successful in that territory, that more were gradually transferred there in later years. By the time the Class 24 arrived in SWA in 1949, there were still 53 Class 7 series locomotives in use there. Most remained there, and were only transferred back to South Africa when the Class 32-000 diesel-electric locomotives replaced them in 1961. In South Africa, they remained in branchline service, particularly at Tarkastad and Ladysmith and also on the Makadas line from Touws River to Ladismith, until they were finally withdrawn in 1972.

Industrial

Four Class 7A locomotives, numbers 992 and 1006, in 1966, and 993 and 1021, in 1971, as well as two Class 7 and two Class 7B, were sold to the Zambesi Saw Mills (ZSM) in Zambia. The company worked the teak forests which stretched 100 miles (160 kilometres) to the north-west of Livingstone, where it built one of the longest logging railways in the world to serve its sawmill at Mulobezi. These eight locomotives joined eight ex RR 7th Class locomotives, which had been acquired by the ZSM between 1925 and 1956.

Railway operations ceased at Mulobezi around 1972, whilst operation of the line to Livingstone was taken over by the Zambia Railways in 1973. While most of the Class 7 series locomotives remained at Mulobezi out of use, Class 7A no. 1021 was installed at the Livingstone factory to supply steam for curing wood.

Sudan's Dongola Class

Sudan Dongola Class (4-8-0), c. 1898

Known as the Dongola Class, Cape 7th Class locomotives were also built for the Soudan Military Railway during Kitchener's campaign in Sudan. When he arrived in the territory in 1895, he built a railway line, strictly for military purposes, running parallel to the Nile River for nearly 200 miles (322 kilometres) from Wadi Halfa to the Third Cataract at Kerma, and then another line from Wadi Halfa across 571 miles (919 kilometres) through the Nubian Desert to Atbarah and on to Khartoum to the south. For motive power, three Cape 7th Class locomotives, built to the Class 7A design, were ordered from Neilson and delivered in 1897. These were followed by five more in two batches in 1898. They were initially not numbered, but named after places in Sudan.

Their works numbers, order numbers, names and eventual Sudan Railway (SR) numbers, are listed in the table. No. 29, which was originally named "Berber", according to Neilson's records, was later renamed "Fashoda/Suakin".

Sudan Dongola Class
Works numbers, names and numbers

Works No.	Order No.	Year	Name	Sudan Ry No.
5232	E791	1897	Dongola	26
5233	E791	1897	Debbeh	27
5234	E791	1897	Korti	28
5280	E795	1898	Berber	29
5281	E795	1898	Khartoum	30
5345	E801	1898	Kassala	31
5346	E801	1898	Atbara	32
5347	E801	1898	Sennar	33

These locomotives were equipped with gates across the open ends of their cabs and pipes under the running board on the right side, which terminated in hose connections below the front buffer beam, so that water tenders could be coupled to the front and they could be run cab forward. The reason was that they were used on a single line, which was still being constructed into the desert from Wadi Halfa, which initially had no water supply at the far end.

For some reason, these locomotives were not popular in the Sudan and they were all withdrawn from service by 1914.

Illustration

The main picture shows ex Cape Eastern System 7th Class no. 726, SAR Class 7A no. 1009, plinthed in Oudtshoorn in the Cape Province, while the following show the locomotive in service and preserved.

• SAR Class 7A 1019 (4-8-0) ex CGR 731.jpg

  Eastern System 7th Class no. 731, later SAR Class 7A no. 1019, at Alice Station, Cape of Good Hope, circa 1900

• CGR 7th no. 722, SAR 7A no. 1005.jpg

  The Governor's train arrives in Fort Beaufort behind 7th Class no. 722, for the opening of the railway station in 1904

• 43 7A 4-8-0 No 1007 at Voorbaai 1997-SEP-04.jpg

  Ex Eastern System 7th Class no. 724, SAR Class 7A no. 1007 with modified Type ZC tender, at Voorbaai, Mosselbaai, 4 September 1997

• SAR Class 7A 1007 (4-8-0) ex CGR 724.JPG

  Ex Eastern System 7th Class no. 724, SAR Class 7A no. 1007, at Voorbaai, Mosselbaai, 12 April 2006