Autorotation

From Infogalactic: the planetary knowledge core
Jump to: navigation, search

<templatestyles src="Module:Hatnote/styles.css"></templatestyles>

This article is about autorotation of rotary wing aircraft. For autorotation of fixed-wing aircraft, see Autorotation (fixed-wing aircraft).
Airflow through a helicopter rotor. Above, the rotor is powered and pushing air downward, generating lift and thrust. Below, the helicopter rotor has lost power, and the craft is making an emergency landing,

Autorotation is a state of flight in which the main rotor system of a helicopter or similar aircraft turns by the action of air moving up through the rotor, as with an autogyro, rather than engine power driving the rotor.[1][2][3] The term autorotation dates to a period of early helicopter development between 1915 and 1920, and refers to the rotors turning without the engine.[4]

In normal powered helicopter flight, air is drawn into the main rotor system from above and exhausted downward, but during autorotation, air moves up into the rotor system from below as the helicopter descends. Autorotation is permitted mechanically because of both a freewheeling unit, which allows the main rotor to continue turning even if the engine is not running, as well as aerodynamic forces of relative wind maintaining rotor speed. It is the means by which a helicopter can land safely in the event of complete engine failure. Consequently, all single-engine helicopters must demonstrate this capability to obtain a type certificate.[5]

The longest autorotation in history was performed by Jean Boulet in 1972 when he reached a record altitude of 12,440 m (40,814 ft) in an Aérospatiale Lama. Because of a −63 °C (−81.4 °F) temperature at that altitude, as soon as he reduced power the engine flamed out and could not be restarted. By using autorotation he was able to land the aircraft safely.[6]

Descent and landing

For a helicopter, "autorotation" refers to the descending maneuver in which the engine is disengaged from the main rotor system and the rotor blades are driven solely by the upward flow of air through the rotor. The freewheeling unit is a special clutch mechanism that disengages anytime the engine rotational speed is less than the rotor rotational speed. If the engine fails, the freewheeling unit automatically disengages the engine from the main rotor allowing the main rotor to rotate freely.

The most common reason for autorotation is an engine malfunction or failure, but autorotation can also be performed in the event of a complete tail rotor failure, or following loss of tail-rotor effectiveness,[7] since there is virtually no torque produced in an autorotation. If altitude permits, autorotations may also be used to recover from vortex ring state.[2] In all cases, a successful landing depends on the helicopter's height and velocity at the commencement of autorotation (see height-velocity diagram).

At the instant of engine failure, the main rotor blades are producing lift and thrust from their angle of attack and velocity. By immediately lowering collective pitch, which must be done in case of an engine failure, the pilot reduces lift and drag and the helicopter begins an immediate descent, producing an upward flow of air through the rotor system. This upward flow of air through the rotor provides sufficient thrust to maintain rotor rotational speed throughout the descent. Since the tail rotor is driven by the main rotor transmission during autorotation, heading control is maintained as in normal flight.

Several factors affect the rate of descent in autorotation: density altitude, gross weight, rotor rotational speed, and forward airspeed. The pilot's primary control of the rate of descent is airspeed. Higher or lower airspeeds are obtained with the cyclic pitch control just as in normal flight. Rate of descent is high at zero airspeed and decreases to a minimum at approximately 50 to 90 knots, depending upon the particular helicopter and the factors previously mentioned. As the airspeed increases beyond the speed that gives minimum rate of descent, the rate of descent increases again. Even at zero airspeed, the rotor is quite effective as it has nearly the drag coefficient of a parachute[8][9] despite having much lower solidity.

When landing from an autorotation, the kinetic energy stored in the rotating blades is used to decrease the rate of descent and make a soft landing. A greater amount of rotor energy is required to stop a helicopter with a high rate of descent than is required to stop a helicopter that is descending more slowly. Therefore, autorotative descents at very low or very high airspeeds are more critical than those performed at the minimum rate of descent airspeed.

Each type of helicopter has a specific airspeed at which a power-off glide is most efficient. The best airspeed is the one that combines the greatest glide range with the slowest rate of descent. The specific airspeed is different for each type of helicopter, yet certain factors (density altitude, wind) affect all configurations in the same manner. The specific airspeed for autorotations is established for each type of helicopter on the basis of average weather and wind conditions and normal loading.

A helicopter operated with heavy loads in high density altitude or gusty wind conditions can achieve best performance from a slightly increased airspeed in the descent. At low density altitude and light loading, best performance is achieved from a slight decrease in normal airspeed. Following this general procedure of fitting airspeed to existing conditions, the pilot can achieve approximately the same glide angle in any set of circumstances and estimate the touchdown point. This optimum glide angle is usually 17-20 degrees.[10]

Autorotational regions

Blade regions in vertical autorotation descent.

During vertical autorotation, the rotor disc is divided into three regions—the driven region, the driving region, and the stall region. The size of these regions vary with the blade pitch, rate of descent, and rotor rotational speed. When changing autorotative rotational speed, blade pitch, or rate of descent, the size of the regions change in relation to each other.

The driven region, also called the propeller region, is the region at the end of the blades. Normally, it consists of about 30 percent of the radius. It is the driven region that produces the most drag. The overall result is a deceleration in the rotation of the blade.

The driving region, or autorotative region, normally lies between 25 to 70 percent of the blade radius, which produces the forces needed to turn the blades during autorotation. Total aerodynamic force in the driving region is inclined slightly forward of the axis of rotation, producing a continual acceleration force. This inclination supplies thrust, which tends to accelerate the rotation of the blade. Driving region size varies with blade pitch setting, rate of descent, and rotor rotational speed.

The inner 25 percent of the rotor blade is referred to as the stall region and operates above its maximum angle of attack (stall angle) causing drag, which slows rotation of the blade. A constant rotor rotational speed is achieved by adjusting the collective pitch so blade acceleration forces from the driving region are balanced with the deceleration forces from the driven and stall regions.

By controlling the size of the driving region, the pilot can adjust autorotative rotational speed. For example, if the collective pitch is raised, the pitch angle increases in all regions. This causes the point of equilibrium to move inboard along the blade’s span, thereby increasing the size of the driven region. The stall region also becomes larger while the driving region becomes smaller. Reducing the size of the driving region causes the acceleration force of the driving region and rotational speed to decrease.

See also

References

  1. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  2. ↑ 2.0 2.1 Bensen, Igor. "How they fly - Bensen explains all" Gyrocopters UK. Accessed: 10 April 2014. Quote: "air.. (is) deflected downward"
  3. ↑ Charnov, Bruce H. Cierva, Pitcairn and the Legacy of Rotary-Wing Flight Hofstra University. Accessed: 22 November 2011.
  4. ↑ "Autorotation", Dictionary.com Unabridged (v 1.1). Random House, Inc. 17 April 2007
  5. ↑ USA Federal Aviation Regulations, §27.71 Autorotation performance
  6. ↑ Autorotation – Learning to Fly Helicopters
  7. ↑ Rotorcraft Flying Handbook Section 11-12, Federal Aviation Administration, Skyhorse Publishing (July 2007) ISBN 978-1-60239-060-7
  8. ↑ Johnson, Wayne. Helicopter theory p109, Courier Dover Publications, 1980. Accessed: 25 February 2012. ISBN 0-486-68230-7
  9. ↑ John M. Seddon, Simon Newman. Basic Helicopter Aerodynamics p52, John Wiley and Sons, 2011. Accessed: 25 February 2012. ISBN 1-119-99410-1
  10. ↑ Paul Cantrell. "Aerodynamics of Autorotation - steady state descent" Copters Accessed: 11 November 2013.

External links

Retrieved from "https://infogalactic.com/w/index.php?title=Autorotation&oldid=717238733"