Watertable control

Watertable control is the practice of controlling the water table in agricultural land by subsurface drainage with proper criteria to improve the crop yield.

Description and definitions

Subsurface land drainage aims at controlling the water table of the groundwater in originally waterlogged land at a depth acceptable for the purpose for which the land is used. The depth of the water table with drainage is greater than without.

Figure 1. Drainage parameters in watertable control

Figure 2. Crop yield (Y) and depth of water table (X in dm)

Purpose

In agricultural land drainage, the purpose of water table control is to establish a depth of the water table (Figure 1) that does no longer interfere negatively with the necessary farm operations and crop yields (Figure 2, made with the SegReg model, see the page: segmented regression).
In addition, land drainage can help with soil salinity control.
The soil's hydraulic conductivity plays an important role in drainage design.

The development of agricultural drainage criteria is required to give the designer and manager of the drainage system a target to achieve in terms of maintenance of an optimum depth of the water table.

Figure 3. Positive and negative effects of land drainage

Optimization

Optimization of the depth of the water table is related the benefits and costs of the drainage system (Figure 3). The shallower the permissible depth of the water table, the lower the cost of the drainage system to be installed to achieve this depth. However, the lowering of the originally too shallow depth by land drainage entails side effects. These have also to be taken into account, including the costs of mitigation of negative side effects.

Figure 4. Example of effects of drain depth

The optimization of drainage design and the development of drainage criteria are discussed in the article on drainage research.

Figure 4 shows an example of the effect of drain depth on soil salinity and various irrigation/drainage parameters as simulated by the SaltMod program.

History

Historically, agricultural land drainage started with the digging of relatively shallow open ditches that received both runoff from the land surface and outflow of groundwater. Hence the ditches had a surface as well as a subsurface drainage function.
By the end of the 19th century and early in the 20th century it was felt that the ditches were a hindrance for the farm operations and the ditches were replaced by buried lines of clay pipes (tiles), each tile about 30 cm long. Hence the term "tile drainage".
Since 1960, one started using long, flexible, corrugated plastic (PVC or PE) pipes that could be installed efficiently in one go by trenching machines. The pipes could be pre-wrapped with an envelope material, like synthetic fibre and geotextile, that would prevent the entry of soil particles into the drains.
Thus, land drainage became a powerful industry. At the same time agriculture was steering towards maximum productivity, so that the installation of drainage systems came in full swing.

Figure 5. Controlled drainage

Environment

As a result of large scale developments, many modern drainage projects were over-designed, while the negative environmental side effects were ignored. In circles with environmental concern, the profession of land drainage got a poor reputation, sometimes justly so, sometimes unjustified, notably when land drainage was confused with the more encompassing activity of wetland reclamation. Nowadays, in some countries, the hardliner trend is reversed. Further, checked or controlled drainage systems were introduced, as shown in Figure 5 and discussed on the page: Drainage system (agriculture).

Drainage design

Figure 6. Geometry of a well drainage system

The design of subsurface drainage systems in terms layout, depth and spacing of the drains is often done using subsurface drainage equations with parameters like drain depth, depth of the water table, soil depth, hydraulic conductivity of the soil and drain discharge. The drain discharge is found from an agricultural water balance.
The computations can be done using computer models like EnDrain.

Drainage by wells

Subsurface drainage of groundwater can also be accomplished by pumped wells (vertical drainage, in contrast to horizontal drainage). Drainage wells have been used extensively in the Salinity Control and Reclamation Program (SCARP) in the Indus valley of Pakistan. Although the experiences were not overly successful, the feasibility of this technique in areas with deep and permeable aquifers is not to be discarded. The well spacings in these areas can be so wide (more than 1000m) that the installation of vertical drainage systems could be relatively cheap compared to horizontal subsurface drainage (drainage by pipes, ditches, trenches, at a spacing of 100m or less). For the design of a well field for control of the water table, the WellDrain model may be helpful.

Classification

A classification of drainage systems is found in the article Drainage system (agriculture).

See also

• Subsurface dyke

External links

• American Wick Drain- Manufacturer of strip drain used in watertable management
• Chapters of ILRI publication 16 on "Drainage Principles and Applications" can be viewed in: https://edepot.wur.nl/262058
• Website on Waterlogging and Land Drainage : [13]
• Various articles on Waterlogging and Land Drainage can be freely downloaded from : [14]
• For answers to frequently asked questions on Waterlogging and Land Drainage see : [15]
• Reports and case studies on Waterlogging and Land Drainage can be consulted at : [16]
• Software on Waterlogging and Land Drainage can be freely downloaded from : [17]
• A model of subsurface groundwater drainage for water table and soil salinity control (SaltMod) can be freely downloaded from : [18]
• The combination of SaltMod with a polygonal model of groundwater flow (SahysMod) can be freely downloaded from : [19]