UHF connector
<templatestyles src="Module:Infobox/styles.css"></templatestyles>
Type | RF coaxial connector | ||
---|---|---|---|
Production history | |||
Designer | E. Clarke Quackenbush[citation needed] | ||
Designed | 1930s | ||
Manufacturer | Various | ||
General specifications | |||
Diameter | 18 mm (0.71 in) (typical) | ||
Cable | Coaxial | ||
Passband | Typically 0-100 MHz | ||
Connector | SO-239 (socket)[1] PL-259 (plug) [2] |
The UHF connector[3] is a World War II or earlier[4][5] threaded RF connector design, from an era when "UHF" referred to frequencies over 30 MHz.[6][7][8] Originally intended for use as a video connector in radar applications, the connector was later used for other RF applications.[citation needed] This connector was developed on basis of a shielded banana plug.[citation needed]
Contents
Design and nomenclature
Originally the connector was designed to carry signals at frequencies up to 300 MHz,[3] but later measurements reveal limitations above 100 MHz.[9] The coupling shell has a 5⁄8 inch 24tpi UNEF standard thread.[3] The most popular cable plug and corresponding chassis-mount socket carry the old Signal Corps nomenclatures PL-259 (plug) and SO-239 (socket).[10] These are also known as Navy type 49190 and 49194 respectively.[11]
PL-259, SO-239, and several other related military references refer to one specific mechanical design collectively known as the UHF Connector.[3]
Characteristics
Mechanical
By design, all connectors in the UHF Connector family mate using the 5/8 inch 24 tpi threaded shell for the shield connection[3] and an approximately 0.156 inch (4mm) diameter pin and socket for the inner conductor.[citation needed] Similar connectors with an incompatible 16mm diameter, 1mm metric thread have been produced,[12] but these are not standard UHF connectors by definition.[3]
Surge impedance
UHF connectors have a non-constant surge impedance.[3] For this reason, UHF connectors are generally usable through HF and the lower portion of what is now known as the VHF frequency range.[9] Despite the name, the UHF connector is rarely used in commercial applications for today's UHF frequencies, as the non-constant surge impedance creates measurable electrical signal reflections above 100 MHz.[9][13][14]
Power
UHF connectors can handle RF peak power levels over one kilowatt based on the voltage rating of 500 volts peak.[3] The average power handling of the PTFE-insulated versions is essentially set by heating of the center pin, and is therefore frequency-dependent, because the RF resistance rises as the skin depth falls.[citation needed]
Environmental tolerance
The UHF connector is not weatherproof.[3]
Applications
In many applications, UHF connectors were replaced by designs that have a more uniform surge impedance over the length of the connector, such as the N connector and the BNC connector.[15] UHF connectors are still widely used in amateur radio, Citizens Band radio, and marine VHF radio applications.[citation needed]
See also
References
- ↑ US patent 2761110, Henry M Diambra, "Solderless Coaxial Connector", published 1956-08-28, assigned to Entron, Inc.
- ↑ US patent 4085366, Billy Padgett, "Noise reduction device for citizen's band transceivers", published 1978-04-18, assigned to Billy Padgett
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 Lua error in package.lua at line 80: module 'strict' not found.
- ↑ US patent 2335041, William A Bruno, "Right-angle electric connector", published 1943-11-23, assigned to Bruno Patents Inc
- ↑ US patent 2422982, Edward Clarke Quackenbush, "Coaxial cable connector", published 1947-06-24, assigned to Edward Clarke Quackenbush
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ 9.0 9.1 9.2 Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ US patent 2233166, William C Hahn, "Means for transferring high frequency power", published 1941-02-25, assigned to Gen Electric
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.