South African Class 6F 4-6-0

This article is about one of several different Cape Government Railways locomotive types to be designated "6th Class". For other CGR 6th Class locomotives, see Cape Government Railways 6th Class locomotives.

CGR 6th Class 4-6-0 1900
South African Class 6F 4-6-0

300px Ex CGR 6th Class, SAR Class 6F

Type and origin Power type Steam Designer Cape Government Railways (H.M. Beatty) Builder Sharp, Stewart and Company Serial number 4631–4632 Model CGR 6th Class Build date 1900 Total produced 2

Specifications Configuration 4-6-0 (Tenwheeler) Driver axle 2nd coupled axle Gauge 3 ft 6 in (1,067 mm) Cape gauge Leading dia Coupled dia 54 in (1,372 mm) Tender wheels Wheelbase  • Engine 20 ft 8 in (6,299 mm)  • Leading 5 ft 6 in (1,676 mm)  • Coupled 11 ft 4 in (3,454 mm)  • Tender 16 ft 1 in (4,902 mm)  • Tender bogie 4 ft 7 in (1,397 mm) Wheel spacing (Assymetrical) 1-2: 4 ft 9 in (1,448 mm) 2-3: 6 ft 7 in (2,007 mm) Length:  • Over couplers Height 12 ft 10 in (3,912 mm) Frame type Bar Axle load  • Leading  • 1st coupled  • 2nd coupled  • 3rd coupled  • Tender bogie Bogie 1: Bogie 2: Adhesive weight Loco weight Tender weight Loco & tender weight Tender type 2-axle bogies Fuel type Coal Fuel capacity 6 LT (6.1 t) Water cap Boiler:  • Pitch 6 ft 9 in (2,057 mm)  • Diameter 4 ft 7 in (1,397 mm)  • Tube plates  • Small tubes 182: 2 in (51 mm)  • Firebox type Round-top Boiler pressure Safety valve Ramsbottom Firegrate area 18.75 sq ft (1.742 m2) Heating surface 1,170 sq ft (109 m2)  • Tubes 1,065 sq ft (98.9 m2)  • Firebox 105 sq ft (9.8 m2) Cylinders Two Cylinder size 17 in (432 mm) bore 26 in (660 mm) stroke Valve gear Stephenson Couplers Bell link-and-pin

Performance figures Tractive effort 18,780 lbf (83.5 kN) @ 75%

Career Operators Cape Government Railways South African Railways Class CGR 6th Class, SAR Class 6F Number in class 2 Numbers CGR 260-261 SAR 604-605 Delivered 1900 First run 1900 Withdrawn 1929

The South African Railways Class 6F 4-6-0 of 1900 was a steam locomotive from the pre-Union era in the Cape of Good Hope.

In 1900, two redesigned 6th Class 4-6-0 steam locomotives were placed in service by the Cape Government Railways. In 1912, when they were assimilated into the South African Railways, they were renumbered and reclassified to Class 6F.

Manufacturer

The original 6th Class 4-6-0 passenger steam locomotive was designed at the Salt River works of the Cape Government Railways (CGR) in 1893, at the same time as the 7th Class, both according to the specifications of Michael Stephens, then Chief Locomotive Superintendent of the CGR, and under the supervision of H.M. Beatty, then Locomotive Superintendent of the Western System. Whereas the 7th Class was conceived primarily as a goods locomotive, the 6th Class was intended to be its fast passenger service counterpart.

File:H.M. Beatty.jpg

H.M. Beatty

The two 6th Class locomotives which were placed in service by the CGR in 1900, were built by Sharp, Stewart and Company, numbered 260 and 261 and allocated to the Western System. They were equipped with large commodious cabs, which were to become standard in all subsequent designs. They had larger heating surfaces and grate areas than any of the previous 6th Class locomotives, with the boiler pressure increased to 180 pounds per square inch (1,241 kilopascals) and with larger tenders, which rode on bogies. In visual appearance, they differed from all previous 6th Class locomotives, by having higher mounted running boards without coupled wheel fairings. They proved to be good engines and were better steamers.

These engines reflected the decision by Beatty, who had succeeded Michael Stephens as Chief Locomotive Superintendent in 1895, to adopt bar frames for future CGR locomotives. He thereby demonstrated that, while still keeping to the good points of the locomotives he had designed under Stephens' supervision, he was preparing to adopt his own ideas in his future locomotive designs.

Class 6 sub-classes

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (CGR, Natal Government Railways and Central South African Railways) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways required careful planning and was only implemented with effect from 1 January 1912.

When these two locomotives were assimilated into the South African Railways (SAR) in 1912, they were renumbered 604 and 605 and designated Class 6F.

The rest of the CGR's 6th Class locomotives, together with 6th Class locomotives which had been inherited from the Oranje-Vrijstaat Gouwerment-Spoorwegen (OVGS) via the Imperial Military Railways (IMR) and the Central South African Railways (CSAR), were grouped into thirteen more sub-classes by the SAR. The 4-6-0 locomotives became SAR Classes 6, 6A to 6E, 6G, 6H and 6J to 6L, the 2-6-2 locomotives became Class 6Y and the 2-6-4 locomotives became Class 6Z.

Service

The Class 6 series of locomotives were introduced primarily as passenger locomotives, but when the class became displaced by larger and more powerful locomotive classes, it literally became a Jack-of-all-trades which proved itself as one of the most useful and successful locomotive classes ever to be designed at the Salt River shops. It went on to see service in all parts of the country, except in Natal, and was used on all types of traffic.

These two Class 6F locomotives were placed in service on the Cape mainline. Compared to most of the rest of the Class 6 family, they had a relatively short lifespan of less than thirty years, and were withdrawn from service by 1929.