Nail (fastener)

A pile of nails
Classification	fastener
Used with	wood

In woodworking and construction, a nail is a pin-shaped object of metal (or wood, called a treenail or "trunnel") which is used as a fastener, as a peg to hang something, or sometimes as a decoration. Generally nails have a sharp point on one end and a flattened head on the other, but headless nails are available. Nails are made in a great variety of forms for specialized purposes. The most common is a wire nail. Other types of nails include pins, tacks, brads, and spikes.

Nails are typically driven into the workpiece by a hammer, a pneumatic nail gun, or a small explosive charge or primer. A nail holds materials together by friction in the axial direction and shear strength laterally. The point of the nail is also sometimes bent over or clinched after driving to prevent pulling out.

History

Nails can be hammered or shot into materials such as wood.

The history of the nail is divided roughly into three distinct periods:

• Hand-wrought (forged) nail (pre-history until 19th century)
• Cut nail (roughly 1800 to 1914)
• Wire nail (roughly 1860 to the present)

Forged nails

Boat nail production in Hainan, China

To make a wrought-iron nail, iron ore was heated with carbon (to create wrought iron) and shaped into square rods. To make a nail, a blacksmith would heat the rod in a forge and taper the end of the bar while keeping the cross section square. Next, the smith cuts off the taper, and inserts it into a nail heading tool with a square hole. The top of the taper is hammered downward (upset) to form a head.

Nails date back at least to Ancient Egypt — bronze nails found in Egypt have been dated 3400 BC. The Bible provides a number of references to nails, including the story in Judges of Jael the wife of Heber, who drives a nail (or tent-peg) into the temple of a sleeping Canaanite commander, the provision of iron for nails by King David for what would become Solomon's Temple, and in connection with the crucifixion of Christ.

The Romans made extensive use of nails - the Roman army,for example, left behind seven tons of nails when it evacuated the fortress of Inchtuthil in Perthshire in the United Kingdom in 86 or 87 CE.

The term "penny", as it refers to nails, probably originated in medieval England to describe the price of 100 nails. Nails themselves were sufficiently valuable and standardized to be used as an informal medium of exchange.

Until around 1800 artisans known as nailers or nailors made nails by hand - note the surname Naylor. (Workmen called slitters cut up iron bars to a suitable size for nailers to work on. From the late 16th century, manual slitters disappeared with the rise of the slitting mill, which cut bars of iron into rods with an even cross-section, saving much manual effort.)

At the time of the American Revolution, England was the largest manufacturer of nails in the world. Nails were expensive and difficult to obtain in the American colonies, so that abandoned houses were sometimes deliberately burned down to allow recovery of used nails from the ashes. Families often had small nail-manufacturing setups in their homes; during bad weather and at night, the entire family might work at making nails for their own use and for barter. Thomas Jefferson wrote in a letter: "In our private pursuits it is a great advantage that every honest employment is deemed honorable. I am myself a nail maker." The growth of the trade in the American colonies was theoretically held back by the prohibition of new slitting mills in America by the Iron Act of 1750, though there is no evidence that the Act was actually enforced.

The production of wrought-iron nails continued well into the 19th century, but ultimately was reduced to nails for purposes for which the softer cut nails were unsuitable, including horseshoe nails.

Cut nails

From the very beginning, nails were handmade; the nail-making process was slow; and nails were relatively few and expensive. This naturally produced a desire to create machines to speed up and automate the nail-making process. The slitting mill, introduced to England in 1590, had simplified the production of nail rods, but the real first efforts to mechanise the nail-making process itself occurred between 1790 and 1820, initially in the United States and England, when various machines were invented to automate and speed up the process of making nails from bars of wrought iron. These nails were known as cut nails or square nails because of their roughly rectangular cross section. Cut nails were one of the important factors in the increase in balloon framing beginning in the 1830s and thus the decline of timber framing with wooden joints. Though still used for historical renovations, and for heavy-duty applications, such as attaching boards to masonry walls, cut nails are much less common today than wire nails.

The cut-nail process was patented in America by Jacob Perkins in 1795 and in England by Joseph Dyer, who set up machinery in Birmingham. The process was designed to cut nails from sheets of iron, while making sure that the fibres of the iron ran down the nails. The Birmingham industry expanded in the following decades, and reached its greatest extent in the 1860s, after which it declined due to competition from wire nails, but continued until the outbreak of World War I.

Wire nails

As the name implies, wire nails are formed from wire. Wire nails are made from coils of wire, usually drawn through a series of dies to reach a specific diameter, then cut into short rods that are then formed into nails. The nail tip is usually cut by a blade; the head is formed by reshaping the other end of the rod under high pressure. Other dies are used to cut groves and ridges. Wire nails were also known as "French nails" for their country of origin. Belgian wire nails were beginning to compete in England in 1863. Joseph Henry Nettlefold was making wire nails at Smethwick by 1875. Over the following decades, the nail-making process was almost completely automated. Eventually the industry had machines capable of quickly producing huge numbers of inexpensive nails with little or no human intervention.

With the introduction of cheap wire nails, the use of wrought iron for nail making quickly declined, as more slowly did the production of cut nails. In the United States, in 1892 more steel-wire nails were produced than cut nails. In 1913, 90% of manufactured nails were wire nails. Nails went from being rare and precious to being a cheap mass-produced commodity. Today almost all nails are manufactured from wire, but the term "wire nail" has come to refer to smaller nails, often available in a wider, more precise range of gauges than is typical for larger common and finish nails.

Materials

Formerly made of bronze or wrought iron, today's nails are typically made of steel, often dipped or coated to prevent corrosion in harsh conditions or improve adhesion. Ordinary nails for wood are usually of a soft, low-carbon or "mild" steel (about 0.1% carbon, the rest iron and perhaps a trace of silicon or manganese). Nails for concrete are harder, with 0.5-0.75% carbon.

Usage

Different types of nails: 1) Roofing nail, 2) Umbrella head roofing nail, 3) Brass escutcheon pin, 4) Finish nail, 5) Concrete nail, 6) Spiral-shank nail, and 7) Ring-shank nail (the barbs are a leftover component of the feed system of a nail gun)

Horseshoe nails

Nail-maker's work-bench or anvil in a storeroom of the Black Country Living Museum

Types of nail include:

• Aluminum nails - Made of aluminum in many shapes and sizes for use with aluminum architectural metals.
• Box nail - like a common nail but with a thinner shank and head
• Brads are small, thin, tapered, nails with a lip or projection to one side rather than a full head or a small finish nail
  • Floor brad ('stigs') - flat, tapered and angular, for use in fixing floor boards
  • Oval brad - Ovals utilize the principles of fracture mechanics to allow nailing without splitting. Highly anisotropic materials like regular wood (as opposed to wood composites) can easily be wedged apart. Use of an oval perpendicular to the wood's grain cuts the wood fibers rather than wedges them apart, and thus allows fastening without splitting, even close to edges.
  • Panel pin
• Tacks are short, sharp pointed nails often used with carpet, fabric and paper. When pushed by hand called a thumb tack or push pin.
  • brass tack - brass tacks are commonly used where corrosion may be an issue, such as furniture where contact with human skin salts will cause corrosion on steel nails.
  • canoe tack
  • carpet tack
  • Upholstery tacks - used to attach coverings to furniture
• Casing nails - have a head that is smoothly tapered, in comparison to the "stepped" head of a finish nail. When used to install casing around windows or doors, they allow the wood to be pried off later with minimal damage when repairs are needed, and without the need to dent the face of the casing in order to grab and extract the nail. Once the casing has been removed, the nails can be extracted from the inner frame with any of the usual nail pullers.
• clout-nail - a roofing nail
• Coffin nail - general name for a nail used in a coffin, slang for a cigarette.
• Coil nail - nails designed for use in a pneumatic nail gun assembled in coils.
• Common nail - smooth shank, wire nail with a heavy, flat head. The typical nail for framing.
• Convex head (nipple head, springhead) roofing nail - an umbrella shaped head with a rubber gasket for fastening metal roofing, usually with a ring shank.
• Copper nail - nails made of copper for use with copper flashing or slate shingles etc.,
• Corrugated fastener (wiggle nail) - a corrugated shaped piece of metal driven into miter joints in some furniture.
• D-head (clipped head) nail - a common or box nail with part of the head removed such as when assembled into a "stick" for some pneumatic nail guns.
• Double-ended nail - a rare type of nail with points on both ends and the "head" in the middle for joining boards together. See this patent. Similar to a dowel nail but with a head on the shank.
• Double-headed (duplex, formwork, shutter, scaffold) nail - used for temporary nailing; nails can easily pulled for later disassembly
• Dowel nail - a double headed nail without a "head" on the shank, a piece of round steel sharpened on both ends.
• Drywall (plasterboard) nail - short, hardened, ring-shank nail with a very thin head.
• Fiber cement nail - a nail for installing fiber cement siding.
• Finish nail (bullet head nail, lost-head nail) - A wire nail with a small head intended to be minimally visible or driven below the wood surface and the hole filled to be invisible. has the same diameter as a box nail
• Gang nail - a nail plate
• Hardboard pin - a small nail for fixing hardboard or thin plywood, often with a square shank
• Horseshoe nail - nails used to hold horseshoes on hoofs
• Joist hanger nail - special nails rated for use with joist hangers and similar brackets. Sometimes called "Teco nails" (1-1/2 x .148 shank nails used in metal connectors such as hurricane ties)
• Lost-head nail - see finish nail.
• Masonry (concrete) - lengthwise fluted, hardened nail for use in concrete
• Oval wire nail - nails with an oval shank
• Panel pin
• Plastic strip
• Gutter spike - Large long nail intended to hold wooden gutters in place.
• Ring (annular, improved, jagged) shank nail - nails that have ridges circling the shank to provide extra resistance to pulling out (for example, the HurriQuake nail)
• Roofing (clout) nail - generally a short nail with a broad head used with asphalt shingles, felt paper or the like.
• Screw (helical) nail - a nail with a spiral shank.
• Shake (shingle) nail - small headed nails to use for nailing shakes and shingles
• Sprig - a small nail with either a headless, tapered shank or a square shank with a head on one side
• Square nail - a cut nail
• T-head nail - shaped like the letter T.
• Veneer pin
• Wire (French) nail - a general term for a nail with a round shank. These are sometimes called French nails from their country of invention.
• Wire-weld collated nail - nails held together with slender wires for use in nail guns.

Sizes

Most countries, except the United States, use a metric system for describing nail sizes. A 50 × 3.0 indicates a nail 50 mm long (not including the head) and 3 mm in diameter. Lengths are rounded to the nearest millimetre.

For example, finishing nail* sizes typically available from German suppliers are:

Length	Diameter
mm	mm
20	1.2
25	1.4
30	1.6
35	1.6
35	1.8
40	2.0
45	2.2
50	2.2
55	2.2
55	2.5
60	2.5
60	2.8
65	2.8
65	3.1
70	3.1
80	3.1
80	3.4
90	3.4
90	3.8
100	3.8
100	4.2
110	4.2
120	4.2
130	4.6
140	5.5
160	5.5
180	6.0
210	7.0

• Drahtstift mit Senkkopf (Stahl, DIN 1151)

United States penny sizes

In the United States, the length of a nail is designated by its penny size, written with a number and the abbreviation d for penny; for example, 10d for a ten-penny nail. A larger number indicates a longer nail, shown in the table below. Nails under 1¼ inch, often called brads, are sold mostly in small packages with only a length designation or with length and wire gauge designations; for example, 1" 18 ga or 3/4" 16 ga.

Penny sizes originally referred to the price for a hundred nails in England in the 15th century: the larger the nail, the higher the cost per hundred. The system remained in use in England into the 20th century, but is obsolete there today. The d is an abbreviation for denarius, a Roman coin similar to a penny; this was the abbreviation for a penny in the UK before decimalisation.

penny size	length (inches)	length (nearest mm)
2d	1	25
3d	1¼	32
4d	1½	38
5d	1¾	44
6d	2	51
7d	2¼	57
8d	2½	65
9d	2¾	70
10d	3	76
12d	3¼	83
16d	3½	89
20d	4	102
30d	4½	115
40d	5	127
50d	5½	140
60d	6	152

Terminology

• Box — a wire nail with a head; box nails have a smaller shank than common nails of the same size
• Bright — no surface coating; not recommended for weather exposure or acidic or treated lumber
• Casing — a wire nail with a slightly larger head than finish nails; often used for flooring
• CC or Coated — "cement coated"; nail coated with adhesive (cement) for greater holding power; also resin- or vinyl-coated; coating melts from friction when driven to help lubricate then adheres when cool; color varies by manufacturer (tan, pink, are common)
• Common — a common construction wire nail with a disk-shaped head that is typically 3 to 4 times the diameter of the shank: common nails have larger shanks than box nails of the same size
• Cut — machine-made square nails. Now used for masonry and historical reproduction or restoration.
• Duplex — a common nail with a second head, allowing for easy extraction; often used for temporary work, such as concrete forms or wood scaffolding; sometimes called a "scaffold nail"
• Drywall — a specialty blued-steel nail with a thin broad head used to fasten gypsum wallboard to wooden framing members
• Finish — a wire nail that has a head only slightly larger than the shank; can be easily concealed by countersinking the nail slightly below the finished surface with a nail-set and filling the resulting void with a filler (putty, spackle, caulk, etc.)
• Forged — handmade nails (usually square), hot-forged by a blacksmith or nailor, often used in historical reproduction or restoration, commonly sold as collectors items
• Galvanized — treated for resistance to corrosion and/or weather exposure
  • Electrogalvanized — provides a smooth finish with some corrosion resistance
  • Hot-dip galvanized — provides a rough finish that deposits more zinc than other methods, resulting in very high corrosion resistance that is suitable for some acidic and treated lumber;
  • Mechanically galvanized — deposits more zinc than electrogalvanizing for increased corrosion resistance

The Iron Roland of Mannheim (1915)

• Head — round flat metal piece formed at the top of the nail; for increased holding power
• Helix — the nail has a square shank that has been twisted, making it very difficult to pull out; often used in decking so they are usually galvanized; sometimes called decking nails
• Length — distance from the bottom of the head to the point of a nail
• Phosphate-coated — a dark grey to black finish providing a surface that binds well with paint and joint compound and minimal corrosion resistance
• Point — sharpened end opposite the "head" for greater ease in driving
• Pole Barn — long shank (2 1/2in to 8in, 6 cm to 20 cm), ring shank (see below), hardened nails; usually oil quenched or galvanized (see above); commonly used in the construction of wood framed, metal buildings (pole barns)
• Ring Shank — small directional rings on the shank to prevent the nail from working back out once driven in; common in drywall, flooring, and pole barn nails
• Shank — the body the length of the nail between the head and the point; may be smooth, or may have rings or spirals for greater holding power
• Sinker — these are the most common nails used in framing today; same thin diameter as a box nail; cement coated (see above); the bottom of the head is tapered like a wedge or funnel and the top of the head is grid embossed to keep the hammer strike from sliding off
• Spike — a large nail; usually over 4 in (100 mm) long
• Spiral — a twisted wire nail; spiral nails have smaller shanks than common nails of the same size

Artistic use

Nails have been used in art, such as the Nail Men - a form of fundraising common in Germany and Austria during World War I.

Before the 1850s bocce and pétanque boules were wooden balls, sometimes partially reinforced with hand-forged nails. When cheap, plentiful machine-made nails became available, manufacturers began to produce the boule cloutée — a wooden core studded with nails to create an all-metal surface. Nails of different metals and colors (steel, brass and copper) were used to create a wide variety of designs and patterns. Some of the old boules cloutées are genuine works of art and valued collectors items.

Once nails became cheap and widely available, they were often used in folk art and outsider art as a method of decorating a surface with metallic studs. Another common artistic use is the construction of sculpture from welded or brazed nails.

See also

• Denailer (a tool that removes used nails)
• Nails (film)
• Rail spike
• Screw
• Truss connector plate

External links

• UK DIY site Description of different types of nails
• US DIY site description of different nails
• Nail forging movie